NetHubQuickBringup

NetHub Quick Start

This document is for customers who are using NetHub for the first time. The goal is to help you complete device and host bring-up as quickly as possible.

If you only care about the currently available solution, keep these points in mind:

• The current primary path is SDIO
• The device runs Wi-Fi backend (fhost / wl80211) + lwIP
• nethub bridges device-side Wi-Fi capabilities to the host
• The control channel and USER virtual channel both run on the same host link

Active directories:

• device side
  • components/net/nethub
  • examples/wifi/nethub
• host side
  • bsp/common/msg_router/linux_host/kernel
  • bsp/common/msg_router/linux_host/userspace/nethub

1. Confirm Two Choices Before Bring-Up

1.1 Choose the Wi-Fi Backend

Default configuration:

• CONFIG_WL80211 is disabled
• fhost is used

If you want to switch to wl80211, enable this option in examples/wifi/nethub/defconfig:

CONFIG_WL80211=y

Notes:

• fhost and wl80211 are mutually exclusive
• The current nethub implementation supports both device-side Wi-Fi backends

1.2 Choose the Control Channel

device and host settings must match:

device configuration	host startup
CONFIG_NETHUB_AT_USE_VCHAN=n	./output/bflbwifid or ./output/bflbwifid -c tty -p /dev/ttyAT0
CONFIG_NETHUB_AT_USE_VCHAN=y	./output/bflbwifid -c vchan

The default configuration is:

CONFIG_NETHUB_AT_USE_VCHAN=n

That means the control channel uses TTY by default.

Additional notes:

• The host side always builds both tty + vchan
• The actual selection happens at bflbwifid runtime

2. Build and Flash the Device Firmware

cd examples/wifi/nethub

# BL616
make CHIP=bl616 BOARD=bl616dk

# BL616CL
make CHIP=bl616cl BOARD=bl616cldk

# BL618DG
make CHIP=bl618dg BOARD=bl618dgdk CPU_ID=ap

Flash example:

cd examples/wifi/nethub
make flash CHIP=bl618dg COMX=/dev/ttyUSB0

The most relevant bring-up configuration is located in:

• examples/wifi/nethub/defconfig

Common options:

• CONFIG_NETHUB=y
• CONFIG_MR_NETDEV=y
• CONFIG_MR_TTY=y
• CONFIG_MR_VIRTUALCHAN=y
• CONFIG_NETHUB_AT_USE_VCHAN=n

3. Build and Start the Host Software

3.1 Build

cd bsp/common/msg_router/linux_host/userspace/nethub
./build.sh build

Artifacts:

• output/mr_sdio.ko
• output/bflbwifid
• output/bflbwifictrl
• output/libnethub_vchan.a
• output/nethub_vchan_app

3.2 Load the Kernel Module

cd bsp/common/msg_router/linux_host/userspace/nethub
sudo ./build.sh load

To unload:

sudo ./build.sh unload

3.3 Start the Host Daemon

Default TTY mode:

sudo ./output/bflbwifid

Explicit TTY mode:

sudo ./output/bflbwifid -c tty -p /dev/ttyAT0

VCHAN mode:

sudo ./output/bflbwifid -c vchan

4. Basic Verification Flow

Recommended sequence:

4.1 Check the Current Status

sudo ./output/bflbwifictrl status

4.2 Scan APs

sudo ./output/bflbwifictrl scan

4.3 Connect to an AP

sudo ./output/bflbwifictrl connect_ap "<ssid>" "<password>"

4.4 Check Status Again

sudo ./output/bflbwifictrl status

If the connection succeeds, you will usually see:

• the backend is connected
• the Wi-Fi state is CONNECTED or GOTIP
• IP / Gateway / Netmask / DNS after an address is assigned

4.5 Disconnect

sudo ./output/bflbwifictrl disconnect

5. Common Commands

The public CLI surface is fixed to 9 commands:

• connect_ap
• disconnect
• scan
• status
• version
• reboot
• ota
• start_ap
• stop_ap

Examples:

sudo ./output/bflbwifictrl version
sudo ./output/bflbwifictrl reboot
sudo ./output/bflbwifictrl start_ap "<ssid>" "<password>"
sudo ./output/bflbwifictrl stop_ap

6. SDIO Hardware Information

For the current customer bring-up path, use SDIO directly. USB / SPI still keep architecture skeletons for now and are not the recommended bring-up path.

6.1 Chip Support Matrix

Interface	BL616 / BL618	BL618DG	BL616CL
SDIO	Supported	Supported	Supported
USB	Planned	Planned	Planned
SPI	Planned	Planned	Planned

6.2 SDIO Pins

Pin Function	BL616 / BL618	BL618DG	BL616CL
SDIO_DAT2	GPIO10	GPIO43	GPIO6
SDIO_DAT3	GPIO11	GPIO44	GPIO7
SDIO_CMD	GPIO12	GPIO45	GPIO8
SDIO_CLK	GPIO13	GPIO46	GPIO9
SDIO_DATA0	GPIO14	GPIO47	GPIO10
SDIO_DATA1	GPIO15	GPIO48	GPIO11

7. USER Virtual Channel

If you need to transfer private messages between the host and device, use the USER virtual channel.

Notes:

• The USER channel and the control channel are parallel logical channels
• It is not a separate physical interface; it is a logical channel carried on the current host link

7.1 device-side APIs

Header:

• components/net/nethub/include/nethub_vchan.h

Common APIs:

int nethub_vchan_user_send(const void *data, uint16_t len);
int nethub_vchan_user_recv_register(nethub_vchan_recv_cb_t recv_cb, void *cb_arg);

7.2 host-side APIs

Header:

• bsp/common/msg_router/linux_host/userspace/nethub/virtualchan/nethub_vchan.h

Common APIs:

int nethub_vchan_init(void);
int nethub_vchan_deinit(void);

int nethub_vchan_user_send(const void *data, size_t len);
int nethub_vchan_user_register_callback(nethub_vchan_recv_callback_t callback);

int nethub_vchan_get_state_snapshot(nethub_vchan_state_snapshot_t *snapshot);

Typical host-side usage order:

1. nethub_vchan_init()
2. nethub_vchan_user_register_callback()
3. nethub_vchan_user_send()
4. Call nethub_vchan_deinit() when finished

If you need to check whether the link is ready, you can optionally query:

• link_state == NETHUB_VCHAN_LINK_UP
  • the link is ready for TX/RX
• host_state == NETHUB_VCHAN_HOST_STATE_DEVICE_RUN
  • the host has completed the handshake with the device

8. Common Issues

8.1 bflbwifid Fails to Start

Check first:

• whether the device and host control backends match
• whether /dev/ttyAT0 exists
• whether mr_sdio.ko has been loaded successfully
• whether the SDIO hardware link is working properly

8.2 connect_ap Succeeds but the Host Has No Network Access

Check first:

• whether status has reached GOTIP
• whether mr_eth0 has an address
• whether services such as NetworkManager or dhcpcd override the NetHub configuration

Notes:

• build.sh builds userspace with ENABLE_NETIF_AUTO_CONFIG=1 by default
• After the device reports GOTIP, the host automatically configures the IP, gateway, and DNS of mr_eth0

8.3 build.sh unload Reports That the Module Is Busy

Check first:

• whether bflbwifid is still running
• whether nethub_vchan_app is still running